Template:Infobox connector
Jump to navigation
Jump to search
[[Category:Infobox templates|Template:Remove first word ]]
[[Category:Infobox templates|Template:Remove first word ]]
![]() | This template uses Lua: |
Template:Infobox connector is an infobox for electrical and (audio/video) signal connectors of all kinds.
The template supports three images:
- image, logo, pinout_image
Image and logo share a 300 pixel wide area - so if both are used then the width of the image should be set to 150 pixels, that is, [[Image:example.jpg|150px]]. If only image and pinout are used, then the size of both should be 300 pixels.
Usage
Template:Parameter names example
Example
![]() ![]() This example is not factual – it is purely illustrative of the infobox. | |||
Type | Analogue video connector | ||
---|---|---|---|
Production history | |||
Designer | Some guy | ||
Designed | Early 1990s | ||
Manufacturer | Initially Toshiba | ||
Produced | Early 1990s to 2005 | ||
Superseded | RF connector | ||
Superseded by | DVI connector (2005) | ||
General specifications | |||
Length | 36 mm (typical) | ||
Width | 25 mm | ||
Height | 6.5 mm | ||
Hot pluggable | Yes | ||
External | External | ||
Audio signal | None | ||
Video signal | Analogue 480i, 480p, 720p, 1080i | ||
Cable | 14 core shielded (25 m max) | ||
Passband | 0–20 GHz | ||
Pins | 14 (6 video, 3 reserved, 2 detect, 3 data) | ||
Connector | DB-25 | ||
Electrical | |||
Signal | 220 volts AC 50 Hz typically | ||
Earth | Dedicate pin | ||
Max. voltage | 450 volts peak | ||
Max. current | 20 amps at 220 volts, 5 amps at 400 volts | ||
Data | |||
Data signal | Resolution and Aspect ratio only | ||
Width | 2 bits | ||
Bitrate | 120 bit/s | ||
Max. devices | 1 | ||
Protocol | Serial | ||
Pin out | |||
![]() | |||
A male connector seen from the front. | |||
Pin | Spec name | Example col title | |
Pin 1 | Y | luminance (0.7 V, 75 Ω) | |
Pin 2 | Y GND | Y ground | |
Pin 3 | Pb | 0.35 V, 75 Ω | |
Pin 4 | Pb GND | ||
Pin 5 | Pr | 0.35 V, 75 Ω | |
Pin 6 | Pr GND | ||
Pin 7 | Reserve link 1 | ||
Pin 8 | Data line 1 |
0 V = 525 lines 2.2 V = 750 lines 5 V = 1125 lines | |
Pin 9 | Data line 2 |
0 V = 59.94i / 60i 5 V = 59.94p / 60p | |
Pin 10 | Reserve link 2 | ||
Pin 11 | Data line 3 |
0 V = 4:3 2.2 V = 4:3 letterbox 5 V = 16:9 | |
Pin 12 | Plug insert detect ground | ||
Pin 13 | Reserve link 3 | ||
Pin 14 | Plug insert detect | output 10 kΩ, input > 100 kΩ | |
C1 | BLUE | Analog Blue Video | |
C2 | GREEN | Analog Green Video | |
C3 | HA_SYNC | Analog Horizontal Sync | |
C4 | RED | Analog Red Video | |
C5 | RETURN | Analog RGB Return and DDC Return | |
C6 | AR_PRE | Acid reflux preventer | |
C7 | AR_ENC | Acid reflux encourager | |
C8 | CHRO | Churro presence detect | |
These are some notes about the pinout of this connector. The pins are razor sharp. |
No description.
Parameter | Description | Type | Status | |||
---|---|---|---|---|---|---|
No parameters specified |
The above documentation is transcluded from Template:Infobox connector/doc. (edit | history) Editors can experiment in this template's sandbox (edit | diff) and testcases (edit) pages. Please add categories to the /doc subpage. Subpages of this template. |